TMP102

Описание

The TMP102 is a two-wire, serial output temperature sensor available in a tiny SOT563 package. Requiring no external components, the TMP102 is capable of reading temperatures to a resolution of 0.0625°C.

The TMP102 features SMBus and two-wire interface compatibility, and allows up to four devices on one bus. It also features an SMB alert function.

The TMP102 is ideal for extended temperature measurement in a variety of communication, computer, consumer, environmental, industrial, and instrumentation applications. The device is specified for operation over a temperature range of –40°C to +125°C.

Note that the TMP102 is a 3.3V device and will require a Logic Level Converter to connect it to a 5V Arduino.

Подключение

The TMP102 is a 3.3V device and therefore it is connected to the Arduino board through a Logic Level Converter:

• LV to the 3.3V pin of the Arduino
• HV to the 5V pin of Arduino
• HV Channel 1 TXO to the SDA pin (analog 4)
• HV Channel 2 TXO to the SCL pin (analog 5)
• Low voltage Channel 1 TXI to the SDA pin of TMP102
• Low voltage Channel 2 TXI to the SCL pin of TMP102
• The RX pins of the Logic Level Converter are not used
• V+ of TMP102 connected to 3.3V
• ADD0 of TMP102 connected to ground
• ALT of TMP102 not connected
• All grounds connected together.

Component side with test overlay:

Пример кода

The following code snippet reads the temperature from the TMP102, converts the raw value to degrees Celsius and Fahrenheit, prints it on an LCD display and sends it to the serial port.

 #include <LiquidCrystal.h>
 #include <Wire.h>
 
 // initialize the library with the numbers of the interface pins
 LiquidCrystal lcd(12, 11, 5, 4, 3, 2);
 
 byte res;
 byte msb;
 byte lsb;
 int val;
 float tC;  // temperature in Celsius
 float tF;  // temperature in Fahrenheit
 
 void setup()
 {
   // set up the LCD's number (col,row): 
   lcd.begin(20, 2);
   lcd.print("Temp");
 
   Serial.begin(9600);
   Wire.begin();
 }
 
 void loop()
 {
   lcd.clear();
   
   /* get new value from TMP102 */
   res = Wire.requestFrom(72,2);
   
   if (res == 2) {
     msb = Wire.receive(); /* Whole degrees */ 
     lsb = Wire.receive(); /* Fractional degrees */ 
     val = ((msb) << 4);   /* MSB */
     val |= (lsb >> 4);    /* LSB */
     
     /* calculate temperature */
     tC = val*0.0625;
     tF = (tC * 9/5) + 32;
     
     /* show temperatures on display */
     lcd.print(tC);
     lcd.print("\xdf""C");
 
     lcd.setCursor(0, 1);
     lcd.print(tF);
     lcd.print("\xdf""F");
 
 
     Serial.print(tC);
     Serial.print("C   ");
     Serial.print(tF);
     Serial.println("F");
 
   }
   else {
     lcd.print("ERR");
     Serial.println("ERROR");
   }
   
   delay(1000);
 }

Материалы

• Источник: TMP102 Wiring
• Описание: Media:TMP102.pdf
• Схема отладочной платы: Media:TMP102_Breakout.pdf
• Подключение к Arduino(5v) используя преобразователь уровней Sparkfun Logic Level Converter: http://forum.sparkfun.com/viewtopic.php?f=8&t=20938&p=97163
• Где купить Sparkfun, [hhttp://test.roboforum.ru/index.html 4Robots] и другие.

↑ http://forum.sparkfun.com/viewtopic.php?f=8&t=20938&p=97163