Дополнительные команды AVR-DOS — различия между версиями

Текущая версия на 08:29, 9 января 2009

Список команд AVR-DOS — список функций библиотеки AVR-DOS.

Содержание

1 Диск/Директория
- 1.1 FileDate
- 1.2 FileTime
2 Файлы
- 2.1 Flush
- 2.2 Get
- 2.3 Put
- 2.4 Seek
3 Свойства файла
- 3.1 LOC
- 3.2 FileAttr
4 Другие
- 4.1 Bload
- 4.2 Bsave
5 Сноски
6 См. также

Диск/Директория

FileDate

Возвращает дату создания или последнего изменения файла.

sDate = FileDate ()

sDate = FileDate (file)

sDate(String)	Дата создания или изменения(?) файла
File(String)	Имя файла в текущей директории^[1]^[2]

Пример вызова:

<source lang="vb"> Print "File demo" Print Filelen( "josef.img") ; " length" ' length of file Print Filetime( "josef.img") ; " time" ' time file was changed Print Filedate( "josef.img") ; " date" ' file date </source>

FileTime

Возвращает время создания или последнего изменения файла.

sTime = FileTime ()

sTime = FileTime (file)

sTime(String)	Время создания или изменения(?) файла
File(String)	Имя файла в текущей директории^[1]^[2]

Пример вызова:

<source lang="vb"> Print "File demo" Print Filelen( "josef.img") ; " length" ' length of file Print Filetime( "josef.img") ; " time" ' time file was changed Print Filedate( "josef.img") ; " date" ' file date </source>

Файлы

Flush

Скидывает кеш текущего файла на диск и обновляет информацию раздела, директории.

Процедура осуществляет запись всей несохраненной информации о/в файле на диск. Обычно запись на диск производится при закрытии файлового потока или переходе на другой сектор файла, однако вы можете поменять параметр cFATDirSaveAtEnd, в этом случае вам придется принудительно сбрасывать изменения файла на диск.

Flush #bFileNumber

Flush

BFileNumber(Byte)	Идентификационный номер открытого файлового потока^[3]. Если не указан, то изменения всех открытых файлов сбрасываются на диск.

Пример вызова:

<source lang="vb"> $include "startup.inc"

'open the file in BINARY mode Open "test.biN" For Binary As #2 Put #2 , B ' write a byte Put #2 , W ' write a word Put #2 , L ' write a long Ltemp = Loc(#2) + 1 ' get the position of the next byte Print Ltemp ; " LOC" ' store the location of the file pointer Print Lof(#2) ; " length of file" Print Fileattr(#2) ; " file mode" ' should be 32 for binary Put #2 , Sn ' write a single Put #2 , Stxt ' write a string

Flush #2 ' flush to disk Close #2 </source>

Get

Reads a byte from the hardware or software UART. Reads data from a file opened in BINARY mode.

GET in combination with the software/hardware UART is provided for compatibility with BASCOM-8051. It reads one byte. GET in combination with the AVR-DOS filesystem is very flexible and versatile. It works on files opened in BINARY mode and you can reads all data types. By default you only need to provide the variable name. When the variable is a byte, 1 byte wil be read. When the variable is a word or integer, 2 bytes will be read. When the variable is a long or single, 4 bytes will be read. When the variable is a string, the number of bytes that will be read is equal to the dimensioned size of the string. DIM S as string * 10 , would read 10 bytes. Note that when you specify the length for a string, the maximum length is 255. The maximum length for a non-string array is 65535. <source lang="vb"> Example : GET #1 , var ,,2 ‘ read 2 bytes, start at current position GET #1, var , PS ‘ start at position stored in long PS GET #1, var , PS, 2 ‘ start at position stored in long PS and read 2 bytes</source>

GET #channel, var

GET #channel, var , [pos] [, length]

#channel(...)	A channel number, which identifies an opened file. This can be a hard coded constant or a variable
Var(...)	The variable or variable array that will be assigned with the data from the file
Pos(...)	This is an optional parameter that may be used to specify the postion where the reading must start from. This must be a long variable
Length(...)	This is an optional parameter that may be used to specify how many bytes must be read from the file.

Пример вызова:

<source lang="vb"> 'for the binary file demo we need some variables of different types Dim B As Byte , W As Word , L As Long , Sn As Single , Ltemp As Long Dim Stxt As String * 10 B = 1 : W = 50000 : L = 12345678 : Sn = 123.45 : Stxt = "test"

'open the file in BINARY mode Open "test.biN" For Binary As #2 Put #2 , B ' write a byte Put #2 , W ' write a word Put #2 , L ' write a long Ltemp = Loc(#2) + 1 ' get the position of the next byte Print Ltemp ; " LOC" ' store the location of the file pointer Print Seek(#2) ; " = LOC+1"

Print Lof(#2) ; " length of file" Print Fileattr(#2) ; " file mode" ' should be 32 for binary Put #2 , Sn ' write a single Put #2 , Stxt ' write a string

Flush #2 ' flush to disk Close #2

'now open the file again and write only the single Open "test.bin" For Binary As #2 L = 1 'specify the file position B = Seek(#2 , L) ' reset is the same as using SEEK #2,L Get #2 , B ' get the byte Get #2 , W ' get the word Get #2 , L ' get the long Get #2 , Sn ' get the single Get #2 , Stxt ' get the string Close #2 </source>

Put

Writes a byte to the hardware or software UART. Writes data to a file opened in BINARY mode.

PUT in combination with the software/hardware UART is provided for compatibility with BASCOM-8051. It writes one byte PUT in combination with the AVR-DOS filesystem is very flexible and versatile. It works on files opened in BINARY mode and you can write all data types. By default you only need to provide the variable name. When the variable is a byte, 1 byte wil be written. When the variable is a word or integer, 2 bytes will be written. When the variable is a long or single, 4 bytes will be written. When the variable is a string, the number of bytes that will be written is equal to the dimensioned size of the string. DIM S as string * 10 , would write 10 bytes. Note that when you specify the length for a string, the maximum length is 255. The maximum length for a non-string array is 65535. Example: <source lang="vb"> PUT #1, var PUT #1, var , , 2 ‘ write 2 bytes at default position PUT #1, var ,PS, 2 ‘ write 2 bytes at location storied in variable PS</source>

PUT #channel, var

PUT #channel, var ,[pos] [,length]

#channel(...)	A channel number, which identifies an opened file. This can be a hard coded constant or a variable.
Var(...)	The variable or variable array that will be written to the file
Pos(...)	This is an optional parameter that may be used to specify the postion where the data must be written to. This must be a long variable.
Length(...)	This is an optional parameter that may be used to specify how many bytes must be written to the file.

Пример вызова:

<source lang="vb"> 'for the binary file demo we need some variables of different types Dim B As Byte , W As Word , L As Long , Sn As Single , Ltemp As Long Dim Stxt As String * 10 B = 1 : W = 50000 : L = 12345678 : Sn = 123.45 : Stxt = "test"

'open the file in BINARY mode Open "test.biN" For Binary As #2 Put #2 , B ' write a byte Put #2 , W ' write a word Put #2 , L ' write a long Ltemp = Loc(#2) + 1 ' get the position of the next byte Print Ltemp ; " LOC" ' store the location of the file pointer Print Seek(#2) ; " = LOC+1"

Print Lof(#2) ; " length of file" Print Fileattr(#2) ; " file mode" ' should be 32 for binary Put #2 , Sn ' write a single Put #2 , Stxt ' write a string

Flush #2 ' flush to disk Close #2

'now open the file again and write only the single Open "test.bin" For Binary As #2 L = 1 'specify the file position B = Seek(#2 , L) ' reset is the same as using SEEK #2,L Get #2 , B ' get the byte Get #2 , W ' get the word Get #2 , L ' get the long Get #2 , Sn ' get the single Get #2 , Stxt ' get the string Close #2 </source>

Seek

Function: Returns the position of the next Byte to be read or written. Statement: Sets the position of the next Byte to be read or written.

This function returns the position of the next Byte to be read or written. If an error occures, 0 is returned. Check DOS-Error in variable gbDOSError^[4].. The statetement also returns an error in the gbDOSerror variable in the event that an error occurs. You can for example not set the fileposition behinds the filesize. In QB/VB the file is filled with 0 bytes when you set the filepointer behind the size of the file. For embedded systems this does not seem a good idea. Seek and Loc seems to do the same function, but take care : the seek function will return the position of the next read/write, while the Loc function returns the position of the last read/write. You may say that Seek = Loc+1. Difference with QB In QB/VB you can use seek to make the file bigger. When a file is 100 bytes long, setting the filepointer to 200 will increase the file with 0 bytes. By design this is not the case in AVR-DOS.

Function: NextReadWrite = Seek (#bFileNumber)

Statement: Seek #bFileNumber, NewPos)

bFileNumber(Byte)	Filenumber, which identifies an opened file
NextReadWrite(Long)	A Long Variable, which is assigned with the Position of the next Byte to be read or written (1-based)
NewPos(Long)	A Long variable that holds the new position the filepointer must be set too.

Пример вызова:

<source lang="vb"> Open "test.biN" For Binary As #2 Put #2 , B ' write a byte Put #2 , W ' write a word Put #2 , L ' write a long Ltemp = Loc(#2) + 1 ' get the position of the next byte Print Ltemp ; " LOC" ' store the location of the file pointer Print Seek(#2) ; " = LOC+1"

Close #2

'now open the file again and write only the single Open "test.bin" For Binary As #2 Seek #2 , Ltemp ' set the filepointer Sn = 1.23 ' change the single value so we can check it better Put #2 , Sn = 1 'specify the file position Close #2 </source>

Свойства файла

LOC

Returns the position of last read or written Byte of the file.

This function returns the position of the last read or written Byte. If an error occurs, 0 is returned. Check DOS-Error in variable gbDOSError^[4].. If the file position pointer is changed with the command SEEK, this function can not be used till the next read/write operation. Difference with QB This function differs from QB. In QB the byte position is divided by 128.

lLastReadWritten = Loc (#bFileNumber)

bFileNumber(Byte)	Filenumber, which identifies an opened file
lLastReadWritten(Long)	Variable, whichsigned with the Position of last read or written Byte (1-based)

Пример вызова:

<source lang="vb"> 'open the file in BINARY mode Open "test.biN" For Binary As #2 Put #2 , B ' write a byte Put #2 , W ' write a word Put #2 , L ' write a long Ltemp = Loc(#2) + 1 ' get the position of the next byte Print Ltemp ; " LOC" ' store the location of the file pointer Print Lof(#2) ; " length of file" Print Fileattr(#2) ; " file mode" ' should be 32 for binary Put #2 , Sn ' write a single Put #2 , Stxt ' write a string

Flush #2 ' flush to disk Close #2 </source>

FileAttr

Возвращает режим открытия файлового потока.

bFileAttribut = FileAttr (bFileNumber)

bFileAttribut(Long)	Режим: 1 - INPUT 2 - OUTPUT 8 - APPEND 32 - BINARY
bFileNumber(Byte)	Идентификационный номер открытого файлового потока^[3]

Пример вызова:

<source lang="vb"> 'open the file in BINARY mode Open "test.biN" For Binary As #2 Print Fileattr(#2) ; " file mode" ' should be 32 for binary Put #2 , Sn ' write a single Put #2 , Stxt ' write a string Close #2 </source>

Другие

Bload

Writes the Content of a File into SRAM.

This function writes the content of a file to a desired space in SRAM. A free handle is needed for this function.

BLoad sFileName, wSRAMPointer

sFileName(Long)	Name of the File to be read
wSRAMPointer(Word)	Variable, which holds the SRAM Address to which the content of the file should be written

Пример вызова:

<source lang="vb"> 'now the good old bsave and bload Dim Ar(100) As Byte , I As Byte For I = 1 To 100 Ar(i) = I ' fill the array Next

Wait 2

W = Varptr(ar(1)) Bsave "josef.img" , W , 100 For I = 1 To 100 Ar(i) = 0 ' reset the array Next

Bload "josef.img" , W ' Josef you are amazing !

For I = 1 To 10 Print Ar(i) ; " " ; Next Print </source>

Bsave

Save a range in SRAM to a Fileю

This function writes a range from the SRAM to a file. A free file handle is needed for this function.

BSave sFileName, wSRAMPointer, wLength

sFileName(Long)	Name of the File to be written
wSRAMPointer(Word)	Variable, which holds the SRAM Address, from where SRAM should be written to a File
wLength(Word)	Count of Bytes from SRAM, which should be written to the file

Пример вызова:

<source lang="vb">'now the good old bsave and bload Dim Ar(100) As Byte , I As Byte For I = 1 To 100 Ar(i) = I ' fill the array Next

Wait 2

W = Varptr(ar(1)) Bsave "josef.img" , W , 100 For I = 1 To 100 Ar(i) = 0 ' reset the array Next

Bload "josef.img" , W ' Josef you are amazing !

For I = 1 To 10 Print Ar(i) ; " " ; Next Print </source>

Сноски

↑ ¹ ² 8.3: имя - 8 символов, расширение - 3 символа, разделитель(точка) - 1 символ, всего не более 12 символов
↑ ¹ ² Если не указано, параметром считается последний файл, выбранный с помощью DIR
↑ ¹ ² Принадлежит целому множеству 0..255, может быть переменной или константой. Используйте числа 1..127 для пользовательских идентификаторов. Для получения свободного идентификатора используйте функцию FreeFile(возвращает 128..255) Ошибка цитирования Неверный тег <ref>: название «identnumber» определено несколько раз для различного содержимого
↑ ¹ ² Коды ошибок

См. также

[dosnames-1] ¹ ² 8.3: имя - 8 символов, расширение - 3 символа, разделитель(точка) - 1 символ, всего не более 12 символов

[dirnames-2] ¹ ² Если не указано, параметром считается последний файл, выбранный с помощью DIR

[identnumber-3] ¹ ² Принадлежит целому множеству 0..255, может быть переменной или константой. Используйте числа 1..127 для пользовательских идентификаторов. Для получения свободного идентификатора используйте функцию FreeFile(возвращает 128..255) Ошибка цитирования Неверный тег <ref>: название «identnumber» определено несколько раз для различного содержимого

[OkrDOS-4] ¹ ² Коды ошибок

[1]

[2]

[3]

[4]

Дополнительные команды AVR-DOS — различия между версиями

Текущая версия на 08:29, 9 января 2009

Содержание

Диск/Директория

FileDate

FileTime

Файлы

Flush

Get

Put

Seek

Свойства файла

LOC

FileAttr

Другие

Bload

Bsave

Сноски

См. также

Навигация

Персональные инструменты

Пространства имён

Варианты

Просмотры

Ещё

Поиск

Навигация

Инструменты

@@ Строка 1: / Строка 1: @@
-[[Категория:МиниБот]]
+[[Категория:AVR-DOS]]
-'''Список команд AVR-DOS''' — нижеследующий список команд для операционной системы [[Запускаем AVR-DOS на SD-Card МиниБота|AVR-DOS]].
+'''Список команд AVR-DOS''' — список функций библиотеки [[AVR-DOS]].
 == Диск/Директория ==
-=== InitFileSystem ===
-Читает Master boot record и partition boot record (Sector) диска(флэш-карты) и инициализирует файловую систему.
-'''Эта функция должна быть вызвана перед любым другим использованием системы!'''
-<code>bErrorCode = InitFileSystem (bPartitionNumber)</code>
-{| class="wikitable"
-| bErrorCode(Byte)
-| Код ошибки, возвращает 0 если система успешно запущена.
-|-
-| bPartitionNumber(Byte)
-| Partitionnumber on the Flashcard Drive (normally 1, but use 0 on mediums without Master boot record)
-|}
-Пример вызова:
-<pre>Dim bErrorCode as Byte
-bErrorCode = InitFileSystem(1)
-If bErrorCode > 0 then
-Print "Error: " ; bErrorCode
-Else
-Print "Filesystem successfully initialized"
-End If
-</pre>
-=== DiskSize ===
-Возвращает размер диска.
-<code>lSize = DiskSize ()</code>
-{| class="wikitable"
-| lSize(Long)
-| Объем диска в КБайтах
-|}
-Пример вызова:
-<pre>Dim Gbtemp1 As Byte ' scratch byte
-Gbtemp1 = Initfilesystem(1) ' we must init the filesystem once
-If Gbtemp1 > 0 Then
-Print #1 , "Error " ; Gbtemp1
-Else
-Print #1 , " OK"
-Print "Disksize : " ; Disksize() ' show disk size in Kbytes
-Print "Disk free: " ; Diskfree() ' show free space too
-End If
-</pre>
-=== DiskFree ===
-Возвращает размер свободного пространства диска.
-<code>lFreeSize = DiskFree ()</code>
-{| class="wikitable"
-| lFreeSize(Long)
-| Размер свободной области в КБайтах
-|}
-Пример вызова:
-<pre>Dim Gbtemp1 As Byte ' scratch byte
-Gbtemp1 = Initfilesystem(1) ' we must init the filesystem once
-If Gbtemp1 > 0 Then
-Print #1 , "Error " ; Gbtemp1
-Else
-Print #1 , " OK"
-Print "Disksize : " ; Disksize() ' show disk size in Kbytes
-Print "Disk free: " ; Diskfree() ' show free space too
-End If
-</pre>
-=== Kill ===
-Удаляет файл с диска. Открытый файл не может быть удален. Специальные символы(WildCards) в имени файла, маски не поддерживаются. Код ошибки хранится в глобальной переменной gDOSError.
-<code>Kill sFileName</code>
-{| class="wikitable"
-| sFileName(String)
-| Имя файла в текущей директории
-|}
-Пример вызова:
-<pre>'We can use the KILL statement to delete a file.
-'A file mask is not supported
-Print "Kill (delete) file demo"
-Kill "test.txt"
-</pre>
-=== Dir ===
-Возвращает имя файла, удовлетворяющее маске.
-Первый вызов функции содержит маску. Все последующие вызовы совершаются без маски. Фактически, когда вы хотите получить имя следующего файла в данной директории, удовлетворяющее маске, вы должны вызывать вариант функции без параметров после первого вызова.
-<code>sFile = Dir(mask)</code>
-<code>sFile = Dir()</code>
-{| class="wikitable"
-| SFile(String)
-| Имя файла. Строка пуста, если больше нет файлов, удовлетворяющих маске
-|-
-| Mask(String)
-| Файловая маска, удовлетворяющая требованиям обычного DOS, напр. *.TXT. Маска *.* удовлетворяет всем файлам
-|}
-Пример вызова:
-<pre>'Lets have a look at the file we created
-Print "Dir function demo"
-S = Dir( "*.*")
-'The first call to the DIR() function must contain a file mask
-' The * means everything.
-'
-While Len(s) > 0 ' if there was a file found
-Print S ; " " ; Filedate() ; " " ; Filetime() ; " " ; Filelen()
-' print file , the date the fime was created/changed , the time and the size of the file
-S = Dir() ' get next
-Wend
-</pre>
-=== FileLen ===
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
-<code>lSize = FileLen (file)</code>
-{| class="wikitable"
-| lSize(Long)
-| Размер файла в Байтах
-|-
-| File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
-|}
-Пример вызова:
-<pre>Print "File demo"
-Print Filelen( "josef.img") ; " length" ' length of file
-Print Filetime( "josef.img") ; " time" ' time file was changed
-Print Filedate( "josef.img") ; " date" ' file date
-</pre>
 === FileDate ===
-Возвращает дату создания или изменения(?) файла.
+Возвращает дату создания или последнего изменения файла.
 <code>sDate = FileDate ()</code>
@@ Строка 160: / Строка 15: @@
 |-
 | File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| Имя файла в текущей директории<ref name="dosnames">'''8.3''': имя - 8 символов, расширение - 3 символа, разделитель(точка) - 1 символ, всего не более 12 символов</ref><ref name="dirnames">Если не указано, параметром считается последний файл, выбранный с помощью [[Основные команды AVR-DOS#Dir|DIR]]</ref>
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> Print "File demo"
 Print Filelen( "josef.img") ; " length" ' length of file
 Print Filetime( "josef.img") ; " time" ' time file was changed
 Print Filedate( "josef.img") ; " date" ' file date
-</pre>
+</source>
 === FileTime ===
-Возвращает время создания или изменения(?) файла.
+Возвращает время создания или последнего изменения файла.
 <code>sTime = FileTime ()</code>
@@ Строка 183: / Строка 38: @@
 |-
 | File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| Имя файла в текущей директории<ref name="dosnames">'''8.3''': имя - 8 символов, расширение - 3 символа, разделитель(точка) - 1 символ, всего не более 12 символов</ref><ref name="dirnames">Если не указано, параметром считается последний файл, выбранный с помощью [[Основные команды AVR-DOS#Dir|DIR]]</ref>
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> Print "File demo"
 Print Filelen( "josef.img") ; " length" ' length of file
 Print Filetime( "josef.img") ; " time" ' time file was changed
 Print Filedate( "josef.img") ; " date" ' file date
-</pre>
+</source>
-=== FileDateTime ===
-Возвращает дату и время создания или изменения(?) файла.
-<code>Var = FileDateTime ()</code>
-<code>Var = FileDateTime (file)</code>
-{| class="wikitable"
-| Var(String)
-| Время создания или изменения(?) файла
-|-
-| File(String)
-| When the target variable is a string, it must be dimensioned with a length of at least 17 bytes.
-|-
-| File(Byte array)
-| When the target variable is a byte array, the array size must be at least 6 bytes.
-|-
-| File(Numeric)
-| When you use a numeric variable, the internal file date and time format will be used.
-|}
-Пример вызова:
-<pre>' Read and print Directory and show Filename, Date, Time, Size
-' for all files matching pStr1 and create/update younger than pDays
-Sub Directorylist(pstr1 As String , Byval Pdays As Word)
-Local lFileName as String * 12 ' hold file name for print
-Local lwCounter as Word , lFileSizeSum as Long ' for summary
-Local lwNow as Word , lwDays as Word
-Local lSec as Byte , lMin as Byte , lHour as byte , lDay as byte , lMonth as byte , lYear as byte
-print "Listing of all Files matching " ; pStr1 ; " and create/last update date within " ; pdays ; " days"
-lwNow = SysDay()
-lwCounter = 0 : lFileSizeSum = 0
-lFileName = Dir(pStr1)
-While lFileName <> ""
-lsec = FileDateTime()
-lwDays = lwNow - SysDay(lDay) ' Days between Now and last File Update; uses lDay, lMonth, lYear
-if lwDays <= pDays then ' days smaller than desired with parameter
-print lFileName ; FileDate() ; " " ; FileTime() ; " " ; filelen()
-incr lwCounter : lFileSizeSum = FileLen() + lFileSizeSum
-end if
-lFileName = Dir()
-WEnd
-print lwCounter ; " File(s) found with " ; lFileSizeSum ; " Byte(s)"
-End Sub
-</pre>
-=== GetAttr ===
-Возвращает атрибуты файла.
-<code>bAttr = FileDate ()</code>
-<code>bAttr = FileDate (file)</code>
-{| class="wikitable"
-| bAttr(Byte)
-| Атрибуты файла, совместимые с DOS-форматом. Байт расшифровывается как 00ADVSHR, где биты 5-0:<br />
-A=Archiv<br />
-D=Directory<br />
-V=Volume ID<br />
-S=System<br />
-H=Hidden<br />
-R=Read Only<br />
-|-
-| File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
-|}
-Пример вызова:
-<pre>Print "File demo"
-Print Filelen( "josef.img") ; " length" ' length of file
-Print Filetime( "josef.img") ; " time" ' time file was changed
-Print Filedate( "josef.img") ; " date" ' file date
-Print Bin(GetAttr(“Josef.img”)) ; “Attributes” ‘ DOS Attributes
-</pre>
-=== Name ===
-Переименовывает файл в текущей директории. Файл с новым именем не должен существовать в текущей директории, иначе команда вернет ошибку. Код ошибки можно посмотреть в глобальной переменной gbDOSError.
-<code>Name <strOldFilename> As <strNewFileName></code>
-{| class="wikitable"
-| strOldFileName(String)
-| Старое имя файла
-|-
-| strNewFileName(String)
-| Новое имя файла
-|}
-Пример вызова:
-<pre>Dim strOldFileName as String * 12
-Dim strNewFileName as String * 12
-strOldFileName = "Data.txt"
-strNewFileName = "Data.bak"
-Name strOldFilename As strNewFileName
-</pre>
-=== ChDir ===
-Изменяет текущую директорию.<br />
-'''Функции Kill, Dir, ChDir, MkDir, RmDir, Name, FileLen, FileDateTime, FileDate, FileTime, GetAttr, Open, BLoad и BSave работают только в текущей директории. Обращаться к файлу с помощью составного пути запрещается!'''
-<code>ChDIR (strDirectoryName)</code>
-{| class="wikitable"
-| strDirectoryName(String)
-| Путь к новой директории, длина не более 8 символов. Допускаются следующие спецсимволы:<br />
-"." - на директорию выше<br />
-"\" - в корень диска
-|}
-Пример вызова:
-<pre>Dim strDirectory as String * 12
-ChDir "SubDir"
-' or
-strDirectory = "SubDir"
-ChDir strDirectory
-' Change to next higher directory
-ChDir "."
-' Change to Root Directory
-strDirectory = "\"
-ChDir strDirectory
-</pre>
-=== MkDir ===
-Создает каталог в текущей директории.
-<code>MkDIR (strDirectoryName)</code>
-{| class="wikitable"
-| strDirectoryName(String)
-| Имя новой директории, не более 8 символов
-|}
-Пример вызова:
-<pre>Dim strDirectory as String * 12
-MkDir "NewDir"
-' or
-strDirectory = "NewDir"
-MkDir strDirectory
-</pre>
-=== RmDir ===
-Удаляет каталог в текущей директории.
-<code>RmDIR (strDirectoryName)</code>
-{| class="wikitable"
-| strDirectoryName(String)
-| Имя каталога для удаления, не более 8 символов
-|}
-Пример вызова:
-<pre>Dim strDirectory as String * 12
-MkDir "NewDir"
-' or
-strDirectory = "NewDir"
-MkDir strDirectory
-</pre>
 == Файлы ==
-=== FreeFile ===
+=== Flush ===
-Возвращает свободный файловый номер(filenumber). Функция обеспечивает совместимость с QB.
+Скидывает кеш текущего файла на диск и обновляет информацию раздела, директории.
-<code>bFileNumber = FreeFile()</code>
-{| class="wikitable"
-| bFileNumber(Byte)
-| Свободный файловый номер, который может использоваться для открытия новых файлов. В отличие от QB, этот файловый номер начинается с 128  и заканчивается 255. Используйте числа 1..127 для пользовательских номеров, чтобы избежать конфликтов номеров при использованиии функции.
-|}
-Пример вызова:
-<pre>Ff = Freefile() ' get file handle
-Open "test.txt" For Input As #ff ' we can use a constant for the file too
-Print Lof(#ff) ; " length of file"
-Print Fileattr(#ff) ; " file mode" ' should be 1 for input
-Do
-Line Input #ff , S ' read a line
-' line input is used to read a line of text from a file
-Print S ' print on terminal emulator
-Loop Until Eof(ff) <> 0
-'The EOF() function returns a non-zero number when the end of the file is reached
-'This way we know that there is no more data we can read
-Close #ff
-</pre>
-=== Open ===
-Открывает устройство.
-<code>OPEN "device" for MODE As #channel</code>
-<code>OPEN file FOR MODE as #channel</code>
-{| class="wikitable"
-| Device
-| The default device is COM1 and you don't need to open a channel to use INPUT/OUTPUT on this device.
-With the implementation of the software UART, the compiler must know to which pin/device you will send/receive the data.
-So that is why the OPEN statement must be used. It tells the compiler about the pin you use for the serial input or output and the baud rate you want to use.
-COMB.0:9600,8,N,2 will use PORT B.0 at 9600 baud with 2 stopbits.
-The format for COM1 and COM2 is : COM1: or COM2:
-There is no speed/baud rate parameter since the default baud rate will be used that is specified with $BAUD or $BAUD1
-The format for the software UART is: COMpin:speed,8,N,stopbits[,INVERTED]
-Where pin is the name of the PORT-pin.
-Speed must be specified and stop bits can be 1 or 2.
-bit data or 8 bit data may be used.
-For parity N, O or E can be used.
-An optional parameter ,INVERTED can be specified to use inverted RS-232.
-Open "COMD.1:9600,8,N,1,INVERTED" For Output As #1 , will use pin PORTD.1 for output with 9600 baud, 1 stop bit and with inverted RS-232.
-For the AVR-DOS filesystem, Device can also be a string or filename constant like
-"readme.txt" or sFileName
-|-
-| Mode
-| You can use BINARY or RANDOM for COM1 and COM2, but for the software UART pins, you must specify INPUT or OUTPUT
-For the AVR-DOS filesystem, MODE may be INPUT, OUTPUT, APPEND or BINARY
-|-
-| Channel
-| The number of the channel to open. Must be a positive constant >0
-For the AVR-DOS filesystem, the channel may be a positive constant or a numeric variable. Note that the AVD-DOS filesystem uses real filehandles. The software UART does not use real file handles.
-|}
-Пример вызова:
-<pre>OPEN "com1:" for binary as #1
-Call test
-End
-Sub test
-Print #1, "test"
-End Sub
-Close #1
-</pre>
-=== Close ===
-Освобождает открытое устройство.
-The statements that support the device are PRINT , INPUT and INPUTHEX , INKEY, WAITKEY.
-Every opened device must be closed using the CLOSE #channel statement. Of course, you must use the same channel number.
-The best place for the CLOSE statement is at the end of your program.
-The INPUT statement in combination with the software UART, will not echo characters back because there is no default associated pin for this.
-For the AVR-DOS filesystem, you may place the CLOSE at any place in your program. This because the filesystem supports real file handles.
-<code>OPEN "device" for MODE As #channel<br />
-...<br />
-CLOSE #channel </code>
-{| class="wikitable"
-| Device
-| The default device is COM1 and you don't need to open a channel to use INPUT/OUTPUT on this device.
-With the implementation of the software UART, the compiler must know to which pin/device you will send/receive the data.
-So that is why the OPEN statement must be used. It tells the compiler about the pin you use for the serial input or output and the baud rate you want to use.
-COMB.0:9600,8,N,2 will use PORT B.0 at 9600 baud with 2 stop bits.
-The format for COM1 is : COM1:
-Some chips have 2 UARTS. You can use COM2: to open the second HW UART.
-The format for the software UART is: COMpin:speed,8,N,stop bits[,INVERTED]
-Where pin is the name of the PORT-pin.
-Speed must be specified and stop bits can be 1 or 2.
-An optional parameter ,INVERTED can be specified to use inverted RS-232.
-Open "COMD.1:9600,8,N,1,INVERTED" For Output As #1 , will use pin PORTD.1 for output with 9600 baud, 1 stop bit and with inverted RS-232
-|-
-|MODE
-|You can use BINARY or RANDOM for COM1 and COM2, but for the software UART pins, you must specify INPUT or OUTPUT
-|-
-|Channel
-|The number of the channel to open. Must be a positive constant >0
-|}
-Пример вызова:
-<pre>$crystal = 10000000 'change to the value of the XTAL you have installed
-Dim B As Byte
-'Optional you can fine tune the calculated bit delay
-'Why would you want to do that?
-'Because chips that have an internal oscillator may not
-'run at the speed specified. This depends on the voltage, temp etc.
-'You can either change $CRYSTAL or you can use
-'BAUD #1,9610
-'In this example file we use the DT006 from www.simmstick.com
-'This allows easy testing with the existing serial port
-'The MAX232 is fitted for this example.
-'Because we use the hardware UART pins we MAY NOT use the hardware UART
-'The hardware UART is used when you use PRINT, INPUT or other related statements
-'We will use the software UART.
-Waitms 100
-'open channel for output
-Open "comd.1:19200,8,n,1" For Output As #1
-Print #1 , "serial output"
-'Now open a pin for input
-Open "comd.0:19200,8,n,1" For Input As #2
-'since there is no relation between the input and output pin
-'there is NO ECHO while keys are typed
-Print #1 , "Number"
-'get a number
-Input #2 , B
-'print the number
-Print #1 , B
-'now loop until ESC is pressed
-'With INKEY() we can check if there is data available
-'To use it with the software UART you must provide the channel
-Do
-'store in byte
-B = Inkey(#2)
-'when the value > 0 we got something
-If B > 0 Then
-Print #1 , Chr(b) 'print the character
-End If
-Loop Until B = 27
-Close #2
-Close #1
+Процедура осуществляет запись всей несохраненной информации о/в файле на диск. Обычно запись на диск производится при закрытии файлового потока или переходе на другой сектор файла, однако вы можете поменять параметр [[Окружение AVR-DOS#Конфигурация файловой системы|cFATDirSaveAtEnd]], в этом случае вам придется принудительно сбрасывать изменения файла на диск.
-'OPTIONAL you may use the HARDWARE UART
-'The software UART will not work on the hardware UART pins
-'so you must choose other pins
-'use normal hardware UART for printing
-'Print B
-'When you dont want to use a level inverter such as the MAX-232
-'You can specify ,INVERTED :
-'Open "comd.0:300,8,n,1,inverted" For Input As #2
-'Now the logic is inverted and there is no need for a level converter
-'But the distance of the wires must be shorter with this
-End
-</pre>
-=== Flush ===
-Write current buffer of File to Card and updates Directory. This function writes all information of an open file, which is not saved yet to the Disk. Normally the Card is updated, if a file will be closed or changed to another sector. When no filenumber is specified, all open files will be flushed.
 <code>Flush #bFileNumber</code>
@@ Строка 554: / Строка 61: @@
 {| class="wikitable"
 | BFileNumber(Byte)
-| Filenumber, which identifies an opened file such as #1 or #ff
+| Идентификационный номер открытого файлового потока<ref name="identnumber">Принадлежит целому множеству 0..255, может быть переменной или константой. Используйте числа 1..127 для пользовательских идентификаторов. Для получения свободного идентификатора используйте функцию [[Основные команды AVR-DOS#FreeFile|FreeFile]](возвращает 128..255)</ref>. Если не указан, то изменения всех открытых файлов сбрасываются на диск.
 |}
 Пример вызова:
-<pre>$include "startup.inc"
+<source lang="vb"> $include "startup.inc"
 'open the file in BINARY mode
@@ Строка 575: / Строка 82: @@
 Flush #2 ' flush to disk
 Close #2
-</pre>
+</source>
-=== Print ===
+=== Get ===
-Send output to the RS-232 port. Writes a string to a file. You can use a semicolon (;) to print more than one variable at one line.
+Reads a byte from the hardware or software UART. Reads data from a file opened in BINARY mode.
-When you end a line with a semicolon, no linefeed will be added. The PRINT routine can be used when you have a RS-232 interface on your uP. The RS-232 interface can be connected to a serial communication port of your computer. This way you can use a terminal emulator as an output device. You can also use the build in terminal emulator. The AVR-DOS filesystem also supports PRINT. But in that case, only strings can be written to disk.
-<code>PRINT var ; " constant" </code>
-{| class="wikitable"
-| Var(...)
-| The variable or constant to print
-|}
-Пример вызова:
+GET in combination with the software/hardware UART is provided for compatibility with BASCOM-8051. It reads one byte.
+GET in combination with the AVR-DOS filesystem is very flexible and versatile. It works on files opened in BINARY mode and you can reads all data types.
+By default you only need to provide the variable name. When the variable is a byte, 1 byte wil be read. When the variable is a word or integer, 2 bytes will be read. When the variable is a long or single, 4 bytes will be read. When the variable is a string, the number of bytes that will be read is equal to the dimensioned size of the string. DIM S as string * 10 , would read 10 bytes.
+Note that when you specify the length for a string, the maximum length is 255. The maximum length for a non-string array is 65535.
+<source lang="vb"> Example :
+GET #1 , var ,,2 ‘ read 2 bytes, start at current position
+GET #1, var , PS ‘ start at position stored in long PS
+GET #1, var , PS, 2 ‘ start at position stored in long PS and read 2 bytes</source>
-<pre>Dim A As Byte , B1 As Byte , C As Integer , S As String * 4
+<code>GET #channel, var</code>
-A = 1
-Print "print variable a " ; A
-Print 'new line
-Print "Text to print." 'constant to print
+<code>GET #channel, var , [pos] [, length]</code>
-B1 = 10
-Print Hex(b1) 'print in hexa notation
-C = &HA000 'assign value to c%
-Print Hex(c) 'print in hex notation
-Print C 'print in decimal notation
-C = -32000
-Print C
-Print Hex(c)
-Rem Note That Integers Range From -32767 To 32768
-End
-</pre>
-=== Write ===
-Writes data to a sequential file. When you write a variables value, you do not write the binary representatrion but the ASCII representation. When you look in a file it contains readable text. When you use PUT, to write binary info, the files are not readable or contain unreadable characters. Strings written are surrounded by string delimeters "". Multiple variables written are separated by a comma. Look to this example:
-<pre>Dim S as String * 10 , W as Word
-S="hello" : W = 100
-OPEN "test.txt" For OUTPUT as #1
-WRITE #1, S , W
-CLOSE #1</pre>
-The file content will look like this : "hello",100. Use INPUT to read the values from value.
-<code>Write #ch , data [,data1]</code>
 {| class="wikitable"
-| Ch(...)
+| #channel(...)
 | A channel number, which identifies an opened file. This can be a hard coded constant or a variable
 |-
-| Data , data1
+| Var(...)
-| A variable who’s content are written to the file
+| The variable or variable array that will be assigned with the data from the file
+|-
+| Pos(...)
+| This is an optional parameter that may be used to specify the postion where the reading must start from. This must be a long variable
+|-
+| Length(...)
+| This is an optional parameter that may be used to specify how many bytes must be read from the file.
 |}
 Пример вызова:
-<pre>Dim S As string * 10 , W As Word ,L As Long
+<source lang="vb"> 'for the binary file demo we need some variables of different types
-S = "write"
+Dim B As Byte , W As Word , L As Long , Sn As Single , Ltemp As Long
-Open "write.dmo" For Output As #2
+Dim Stxt As String * 10
-Write #2 , S , W , L ' write is also supported
+B = 1 : W = 50000 : L = 12345678 : Sn = 123.45 : Stxt = "test"
-Close #2
-Open "write.dmo" For Input As #2
-Input #2 , S , W , L ' write is also supported
-Close #2
-Print S ; " " ; W ; " " ; L
-</pre>
-=== Input ===
+'open the file in BINARY mode
-Read a Line from an opened File. Only valid for files opened in mode INPUT. Line INPUT works only with strings. It is great for working on text files.
+Open "test.biN" For Binary As #2
+Put #2 , B ' write a byte
+Put #2 , W ' write a word
+Put #2 , L ' write a long
+Ltemp = Loc(#2) + 1 ' get the position of the next byte
+Print Ltemp ; " LOC" ' store the location of the file pointer
+Print Seek(#2) ; " = LOC+1"
-<code>LineInput #bFileNumber, sLineText</code>
+Print Lof(#2) ; " length of file"
+Print Fileattr(#2) ; " file mode" ' should be 32 for binary
+Put #2 , Sn ' write a single
+Put #2 , Stxt ' write a string
-{| class="wikitable"
+Flush #2 ' flush to disk
-| BfileNumber(Byte)
+Close #2
-| Filenumber, which identifies an opened file
-|-
-| SlineText(String)
-| A string, which is assigned with the next line from the file
-|}
-Пример вызова:
+'now open the file again and write only the single
+Open "test.bin" For Binary As #2
+L = 1 'specify the file position
+B = Seek(#2 , L) ' reset is the same as using SEEK #2,L
+Get #2 , B ' get the byte
+Get #2 , W ' get the word
+Get #2 , L ' get the long
+Get #2 , Sn ' get the single
+Get #2 , Stxt ' get the string
+Close #2
+</source>
-<pre>'Ok we want to check if the file contains the written lines
+=== Put ===
-Ff = Freefile() ' get file handle
+Writes a byte to the hardware or software UART. Writes data to a file opened in BINARY mode.
-Open "test.txt" For Input As #ff ' we can use a constant for the file too
-Print Lof(#ff) ; " length of file"
-Print Fileattr(#ff) ; " file mode" ' should be 1 for input
-Do
-Line Input #ff , S ' read a line
-' line input is used to read a line of text from a file
-Print S ' print on terminal emulator
-Loop Until Eof(ff) <> 0
-'The EOF() function returns a non-zero number when the end of the file is reached
-'This way we know that there is no more data we can read
-Close #ff
-</pre>
-=== Line Input ===
+PUT in combination with the software/hardware UART is provided for compatibility with BASCOM-8051. It writes one byte
-=== FileLen ===
+PUT in combination with the AVR-DOS filesystem is very flexible and versatile. It works on files opened in BINARY mode and you can write all data types.
-Возвращает размер файла.
+By default you only need to provide the variable name. When the variable is a byte, 1 byte wil be written. When the variable is a word or integer, 2 bytes will be written. When the variable is a long or single, 4 bytes will be written. When the variable is a string, the number of bytes that will be written is equal to the dimensioned size of the string. DIM S as string * 10 , would write 10 bytes.
+Note that when you specify the length for a string, the maximum length is 255. The maximum length for a non-string array is 65535.
+Example:
+<source lang="vb"> PUT #1, var
+PUT #1, var , , 2 ‘ write 2 bytes at default position
+PUT #1, var ,PS, 2 ‘ write 2 bytes at location storied in variable PS</source>
-<code>lSize = FileLen ()</code>
+<code>PUT #channel, var</code>
-<code>lSize = FileLen (file)</code>
+<code>PUT #channel, var ,[pos] [,length]</code>
 {| class="wikitable"
-| lSize(Long)
+| #channel(...)
-| Размер файла в Байтах
+| A channel number, which identifies an opened file. This can be a hard coded constant or a variable.
+|-
+| Var(...)
+| The variable or variable array that will be written to the file
+|-
+| Pos(...)
+| This is an optional parameter that may be used to specify the postion where the data must be written to. This must be a long variable.
 |-
-| File(String)
+| Length(...)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| This is an optional parameter that may be used to specify how many bytes must be written to the file.
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> 'for the binary file demo we need some variables of different types
-Print Filelen( "josef.img") ; " length" ' length of file
+Dim B As Byte , W As Word , L As Long , Sn As Single , Ltemp As Long
-Print Filetime( "josef.img") ; " time" ' time file was changed
+Dim Stxt As String * 10
-Print Filedate( "josef.img") ; " date" ' file date
+B = 1 : W = 50000 : L = 12345678 : Sn = 123.45 : Stxt = "test"
-</pre>
-=== Get ===
+'open the file in BINARY mode
-=== FileLen ===
+Open "test.biN" For Binary As #2
-Возвращает размер файла.
+Put #2 , B ' write a byte
+Put #2 , W ' write a word
+Put #2 , L ' write a long
+Ltemp = Loc(#2) + 1 ' get the position of the next byte
+Print Ltemp ; " LOC" ' store the location of the file pointer
+Print Seek(#2) ; " = LOC+1"
-<code>lSize = FileLen ()</code>
+Print Lof(#2) ; " length of file"
+Print Fileattr(#2) ; " file mode" ' should be 32 for binary
+Put #2 , Sn ' write a single
+Put #2 , Stxt ' write a string
-<code>lSize = FileLen (file)</code>
+Flush #2 ' flush to disk
+Close #2
-{| class="wikitable"
+'now open the file again and write only the single
-| lSize(Long)
+Open "test.bin" For Binary As #2
-| Размер файла в Байтах
+L = 1 'specify the file position
-|-
+B = Seek(#2 , L) ' reset is the same as using SEEK #2,L
-| File(String)
+Get #2 , B ' get the byte
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+Get #2 , W ' get the word
-|}
+Get #2 , L ' get the long
+Get #2 , Sn ' get the single
+Get #2 , Stxt ' get the string
+Close #2
+</source>
-Пример вызова:
+=== Seek ===
+Function: Returns the position of the next Byte to be read or written.
+Statement: Sets the position of the next Byte to be read or written.
-<pre>Print "File demo"
+This function returns the position of the next Byte to be read or written. If an error occures, 0 is returned. Check DOS-Error in variable gbDOSError<ref name="OkrDOS">[[Окружение AVR-DOS#Коды ошибок|Коды ошибок]]</ref>..
-Print Filelen( "josef.img") ; " length" ' length of file
+The statetement also returns an error in the gbDOSerror variable in the event that an error occurs.
-Print Filetime( "josef.img") ; " time" ' time file was changed
+You can for example not set the fileposition behinds the filesize.
-Print Filedate( "josef.img") ; " date" ' file date
+In QB/VB the file is filled with 0 bytes when you set the filepointer behind the size of the file. For embedded systems this does not seem a good idea.
-</pre>
+Seek and Loc seems to do the same function, but take care : the seek function will return the position of the next read/write, while the Loc function returns the position of the last read/write. You may say that Seek = Loc+1.
+'''Difference with QB'''
+In QB/VB you can use seek to make the file bigger. When a file is 100 bytes long, setting the filepointer to 200 will increase the file with 0 bytes. By design this is not the case in AVR-DOS.
-=== Put ===
+<code>Function: NextReadWrite = Seek (#bFileNumber)
-=== FileLen ===
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
+Statement: Seek #bFileNumber, NewPos)</code>
-<code>lSize = FileLen (file)</code>
 {| class="wikitable"
-| lSize(Long)
+| bFileNumber(Byte)
-| Размер файла в Байтах
+| Filenumber, which identifies an opened file
 |-
-| File(String)
+| NextReadWrite(Long)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| A Long Variable, which is assigned with the Position of the next Byte to be read or written (1-based)
+|-
+| NewPos(Long)
+| A Long variable that holds the new position the filepointer must be set too.
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> Open "test.biN" For Binary As #2
-Print Filelen( "josef.img") ; " length" ' length of file
+Put #2 , B ' write a byte
-Print Filetime( "josef.img") ; " time" ' time file was changed
+Put #2 , W ' write a word
-Print Filedate( "josef.img") ; " date" ' file date
+Put #2 , L ' write a long
-</pre>
+Ltemp = Loc(#2) + 1 ' get the position of the next byte
+Print Ltemp ; " LOC" ' store the location of the file pointer
+Print Seek(#2) ; " = LOC+1"
-=== Seek ===
+Close #2
-=== FileLen ===
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
+'now open the file again and write only the single
+Open "test.bin" For Binary As #2
-<code>lSize = FileLen (file)</code>
+Seek #2 , Ltemp ' set the filepointer
+Sn = 1.23 ' change the single value so we can check it better
-{| class="wikitable"
+Put #2 , Sn = 1 'specify the file position
-| lSize(Long)
+Close #2
-| Размер файла в Байтах
+</source>
-|-
-| File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
-|}
-Пример вызова:
-<pre>Print "File demo"
-Print Filelen( "josef.img") ; " length" ' length of file
-Print Filetime( "josef.img") ; " time" ' time file was changed
-Print Filedate( "josef.img") ; " date" ' file date
-</pre>
 == Свойства файла ==
-=== EOF ===
+=== LOC ===
-=== FileLen ===
+Returns the position of last read or written Byte of the file.
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
+This function returns the position of the last read or written Byte. If an error occurs, 0 is returned. Check DOS-Error in variable gbDOSError<ref name="OkrDOS">[[Окружение AVR-DOS#Коды ошибок|Коды ошибок]]</ref>.. If the file position pointer is changed with the command SEEK, this function can not be used till the next read/write operation.
+'''Difference with QB'''
+This function differs from QB. In QB the byte position is divided by 128.
-<code>lSize = FileLen (file)</code>
+<code>lLastReadWritten = Loc (#bFileNumber)</code>
 {| class="wikitable"
-| lSize(Long)
+| bFileNumber(Byte)
-| Размер файла в Байтах
+| Filenumber, which identifies an opened file
 |-
-| File(String)
+| lLastReadWritten(Long)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| Variable, whichsigned with the Position of last read or written Byte (1-based)
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> 'open the file in BINARY mode
-Print Filelen( "josef.img") ; " length" ' length of file
+Open "test.biN" For Binary As #2
-Print Filetime( "josef.img") ; " time" ' time file was changed
+Put #2 , B ' write a byte
-Print Filedate( "josef.img") ; " date" ' file date
+Put #2 , W ' write a word
-</pre>
+Put #2 , L ' write a long
+Ltemp = Loc(#2) + 1 ' get the position of the next byte
+Print Ltemp ; " LOC" ' store the location of the file pointer
+Print Lof(#2) ; " length of file"
+Print Fileattr(#2) ; " file mode" ' should be 32 for binary
+Put #2 , Sn ' write a single
+Put #2 , Stxt ' write a string
-=== LOC ===
+Flush #2 ' flush to disk
-=== FileLen ===
+Close #2
-Возвращает размер файла.
+</source>
-<code>lSize = FileLen ()</code>
+=== FileAttr ===
+Возвращает [[Окружение AVR-DOS#Использование команд ввода-вывода в различных режимах|режим открытия]] файлового потока.
-<code>lSize = FileLen (file)</code>
+<code>bFileAttribut = FileAttr (bFileNumber)</code>
 {| class="wikitable"
-| lSize(Long)
+| bFileAttribut(Long)
-| Размер файла в Байтах
+| Режим:
+'''1''' - INPUT<br/>
+'''2''' - OUTPUT<br/>
+'''8''' - APPEND<br/>
+'''32''' - BINARY
 |-
-| File(String)
+| bFileNumber(Byte)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| Идентификационный номер открытого файлового потока<ref name="identnumber">Принадлежит целому множеству 0..255, может быть переменной или константой. Используйте числа 1..127 для пользовательских идентификаторов. Для получения свободного идентификатора используйте функцию [[#FreeFile|FreeFile]](возвращает 128..255)</ref>
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> 'open the file in BINARY mode
-Print Filelen( "josef.img") ; " length" ' length of file
+Open "test.biN" For Binary As #2
-Print Filetime( "josef.img") ; " time" ' time file was changed
+Print Fileattr(#2) ; " file mode" ' should be 32 for binary
-Print Filedate( "josef.img") ; " date" ' file date
+Put #2 , Sn ' write a single
-</pre>
+Put #2 , Stxt ' write a string
+Close #2
+</source>
-=== LO ===
+== Другие ==
-=== FileLen ===
+=== Bload ===
-Возвращает размер файла.
+Writes the Content of a File into SRAM.
-<code>lSize = FileLen ()</code>
+This function writes the content of a file to a desired space in SRAM. A free handle is needed for this function.
-<code>lSize = FileLen (file)</code>
+<code>BLoad sFileName, wSRAMPointer</code>
 {| class="wikitable"
-| lSize(Long)
+| sFileName(Long)
-| Размер файла в Байтах
+| Name of the File to be read
 |-
-| File(String)
+| wSRAMPointer(Word)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| Variable, which holds the SRAM Address to which the content of the file should be written
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb"> 'now the good old bsave and bload
-Print Filelen( "josef.img") ; " length" ' length of file
+Dim Ar(100) As Byte , I As Byte
-Print Filetime( "josef.img") ; " time" ' time file was changed
+For I = 1 To 100
-Print Filedate( "josef.img") ; " date" ' file date
+Ar(i) = I ' fill the array
-</pre>
+Next
-=== FileAttr ===
+Wait 2
-=== FileLen ===
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
+W = Varptr(ar(1))
+Bsave "josef.img" , W , 100
+For I = 1 To 100
+Ar(i) = 0 ' reset the array
+Next
-<code>lSize = FileLen (file)</code>
+Bload "josef.img" , W ' Josef you are amazing !
-{| class="wikitable"
-| lSize(Long)
-| Размер файла в Байтах
-|-
-| File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
-|}
-Пример вызова:
+For I = 1 To 10
+Print Ar(i) ; " " ;
-<pre>Print "File demo"
+Next
-Print Filelen( "josef.img") ; " length" ' length of file
+Print
-Print Filetime( "josef.img") ; " time" ' time file was changed
+</source>
-Print Filedate( "josef.img") ; " date" ' file date
-</pre>
+=== Bsave ===
+Save a range in SRAM to a Fileю
-== Другие ==
+This function writes a range from the SRAM to a file. A free file handle is needed for this function.
-=== Bload ===
-=== FileLen ===
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
+<code>BSave sFileName, wSRAMPointer, wLength</code>
-<code>lSize = FileLen (file)</code>
 {| class="wikitable"
-| lSize(Long)
+| sFileName(Long)
-| Размер файла в Байтах
+| Name of the File to be written
 |-
-| File(String)
+| wSRAMPointer(Word)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
+| Variable, which holds the SRAM Address, from where SRAM should be written to a File
+|-
+| wLength(Word)
+| Count of Bytes from SRAM, which should be written to the file
 |}
 Пример вызова:
-<pre>Print "File demo"
+<source lang="vb">'now the good old bsave and bload
-Print Filelen( "josef.img") ; " length" ' length of file
+Dim Ar(100) As Byte , I As Byte
-Print Filetime( "josef.img") ; " time" ' time file was changed
+For I = 1 To 100
-Print Filedate( "josef.img") ; " date" ' file date
+Ar(i) = I ' fill the array
-</pre>
+Next
-=== Bsave ===
+Wait 2
-=== FileLen ===
-Возвращает размер файла.
-<code>lSize = FileLen ()</code>
+W = Varptr(ar(1))
+Bsave "josef.img" , W , 100
+For I = 1 To 100
+Ar(i) = 0 ' reset the array
+Next
-<code>lSize = FileLen (file)</code>
+Bload "josef.img" , W ' Josef you are amazing !
-{| class="wikitable"
-| lSize(Long)
-| Размер файла в Байтах
-|-
-| File(String)
-| Имя файла в текущей директории. Если не указано, параметром считается последний файл, выбранный с помощью DIR()
-|}
-Пример вызова:
+For I = 1 To 10
+Print Ar(i) ; " " ;
+Next
+Print
+</source>
-<pre>Print "File demo"
+== Сноски ==
-Print Filelen( "josef.img") ; " length" ' length of file
+<references />
-Print Filetime( "josef.img") ; " time" ' time file was changed
-Print Filedate( "josef.img") ; " date" ' file date
-</pre>
 == См. также ==
-* [[Запускаем AVR-DOS на SD-Card МиниБота]]
+* [[AVR-DOS]]
-* [http://members.aon.at/voegel/index.html Официальная страница AVR-DOS]
+* [[Основные команды AVR-DOS]]